Your Plumbing Crash Course: Tips for Installing a Bathtub
Your Plumbing Crash Course: Tips for Installing a Bathtub
Blog Article
We've stumbled on this post relating to Tools You Need to Install a New Bathtub directly below on the web and decided it made sense to relate it with you here.
Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is additionally a reasonably hard task. If the old bathtub is readily available, the task can relocate immediately; if you have to open up a wall surface to get rid of the old tub as well as place the new bath tub, the job is much harder. In either situation, the job is within a residence handyman's skills, although you will need an assistant to vacate the old tub and embeded in the new one. See to it you have qualified on your own for the job as well as are comfortable trying it. Rather than working with a specialist to take over a halfway-completed job, it is far better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly aid you mount a new bathtub in your shower room if you have actually currently bought a new tub as well as don't require to alter the plan of your previous water pipes.
Your tools as well as material list need to consist of the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bathroom must be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of both taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should currently prepare to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly problematic because of the restricted access that is often the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a fabric ready for the remaining water that will come from the pipes. When the supply pipelines have actually been removed, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any old securing compound.
Prior to proceeding to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, put the bath tub in the called for position. The wooden boards are useful in uniformly spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the level and changing the feet on the bath tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the water system as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bathtub as well as likewise check the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub needs to wait until the bath tub has actually been made use of at least when as this will settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making sure that the washers remain in location between the faucet as well as the sink. Safeguard the faucet in place with the maker offered backnut. As soon as the faucet is safely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical tap ports. The former kind must be linked to the faucet finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bathroom as well as the tiling, causing issues with dampness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the movement experienced when the bathtub is in usage. The sealer can fracture fairly very early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very fascinated by How to Install a Bathtub Yourself and I am hoping you liked my blog posting. Liked our article? Please share it. Let someone else find it. Many thanks for going through it.
Ready to assist. Report this page